Featured
-
Wholesale China COD&Ammonia&TN&TP etc Quotes Manufacturer - TPG-3030 Industrial Total Phosphorus Analyzer – BOQU
The sample to be tested does not require any pretreatment. The water sample riser is directly inserted into the system water sample, and the total phosphorus concentration can be measured. The maximum measurement range of this equipment is 0.1~500mg/L TP. This method is mainly used for on-line automatic monitoring of total phosphorus concentration of waste (sewage) water discharge point source, surface water, etc. -
GSGG-5089Pro Industrial Silicate Analyzer – BOQU
1. Low detection limit, very suitable for power plant water feed, saturated steam and superheated steam silicon content detection and control; 2. Long life light source, using cold monochrome light source; 3. Historical curve recording function, can store 30 days of data; 4. Automatic calibration function, period arbitrarily set; 5. Support multi-channel measurements in water samples, optional 1-6 channels; 6. Achieve a maintenance-free, except adding reagents, guide standards. -
Wholesale China Ph Temperature Monitor Manufacturers Pricelist - PH8011 Industrial Antimony PH Sensor – BOQU
Features 1. It adopts the world-class solid dielectric and a large area of PTFE liquid for junction, difficult to block and easy to maintain. 2. Long-distance reference diffusion channel greatly extends the service life of electrodes in the harsh environment. 3. There is no need for additional dielectric and there is a little amount of maintenance. 4. High accuracy, fast response and good repeatability. -
China Wholesale Ntu Turbidity Meter Suppliers Factories - TCS-1000/TS-MX Industrial Sludge Concentration Sensor – BOQU
Features 1. Check and clean window every month, with automatic cleaning brush, brush a half hour. 2. Adopt sapphire glass realize easy maintain, when cleaning adopt scratch-resistant sapphire glass, don’t worry about the wear surface of window. 3. Compact, not fussy installation place, just put in to can complete the installation. 4. Continuous measurement can be achieved, built-in 4~20mA analog output, can transmit data to the various machine according to the need. 5. Wide measurement range,... -
China Wholesale Electrical Conductivity Meter Manufacturers Pricelist - DDG-GY Industrial Inductive Conductivity/TDS Sensor – BOQU
Features 1. Performance in harsh chemical environments is excellent, chemical resistant material manufactured by the electrode is not polarized interference, to avoid dirt, grime and even affect fouling layer covering phenomena such as very poor, simple and easy to install so it’s a very wide range of applications. Design electrodes applied to a high concentration of acids (such as fuming sulfuric acid) environment. 2. English acid concentration meter use, high accuracy, and high stabil... -
China Wholesale Digital Orp/Ph Controller Quotes Manufacturer - PH8083A&AH Industrial ORP Sensor – BOQU
Features ● It adopts gel or solid electrolyte, resisting pressure and helping reduce resistance; low resistance sensitive membrane. ● Waterproof connector can be used for pure water testing. ●There is no need for additional dielectric and there is a little amount of maintenance. ● It adopts BNC connector, which can be replaced by any electrode from abroad. It can be used in conjunction with 361 L stainless steel sheath or PPS sheath. -
China Wholesale Ph And Ec Meter Quotes Manufacturer - PH8022 Industrial Pure Water PH Sensor – BOQU
Model No.: PH8022 Measuring range: 0-14pH Temperature range:0-60℃ Compressive strength:0.6MPa Slope: ≥96％ Zero point potential: E0=7PH±0.3 Internal impedance: ≤250 MΩ (25℃) Profile: 3-in-1Electrode (Integrating the temperature compensation and the solution grounding) Installation size: Upper and Lower 3/4NPT Pipe Thread Connection: Low-noise cable goes out directly. Application: Measurement of all kinds of pure water and high-purity water. ● It adopts the world-cla... -
Wholesale China In Line Ph Controller Manufacturers Pricelist - PH5806 High Temperature PH Sensor – BOQU
Features 1. It adopts heat-resisting gel dielectric and solid dielectric double liquid junction structure; in the circumstances when the electrode is not connected to the back pressure, the withstand pressure is 0~6Bar. It can be directly used for l30℃ sterilization. 2. There is no need for additional dielectric and there is a little amount of maintenance. 3. It adopts S8 and PGl3.5 thread socket, which can be replaced by any overseas electrode. 4. For the electrode length, there are 120, 150...
